View Factor DFF + Bonus - Page 16

KETCH ROSSI · 02-28-2008, 02:06 PM

Quote:

Originally Posted by rgdfilmsRED

Ketch, glad to see that you were able to sell one of your babies off

Can't wait to see what you shoot with your Red

Thanks rgdfilms!

But the camera has not as yet sold as no money has been exchanged as yet, and it could be likely that such a deal will not take place after all, do to few of the RED restrictions, and few of my own!

But one thing for sure, my babies are finally about to come home one way or an other, that I can guarantee!

Ciao,

KETCH ROSSI

Zach Hilton · 03-06-2008, 09:34 PM

Quote:

Originally Posted by CVB

Hopefully this week. If not then very early next week. This web store is taking awhile to get setup and I definitely don't want to go the paper route again for pre-orders.

What's the word on the street for pre-ordering?

John V · 03-07-2008, 04:03 PM

Curt has been in Hanover, Germany for Cebit for the past week. He will be back in the next few days. We expect to get the ordering system up within the next week depending on the schedule he gives me.

Zach Hilton · 03-07-2008, 08:06 PM

Quote:

Originally Posted by johnvon12

Curt has been in Hanover, Germany for Cebit for the past week. He will be back in the next few days. We expect to get the ordering system up within the next week depending on the schedule he gives me.

Alright! Thanks for answering la pregunta.

Adrian T. · 03-08-2008, 10:01 AM

Curt, please take into consideration that the INCLINO mount will be low profile.

As you can see on the following picture, the RED universal mount is too high to pass over an OConnor mount when using the ET bridge plate on a ET dovetail plate (green line marks the problem area).

The mount of the ET bridge plate (right below the front of the camera) is way smaller.

The space between the rods and the silver lever of the OConnor head is approximately 13 mm. So please try to make your mount smaller than that.

John V · 03-08-2008, 12:19 PM

Just a quick comment regarding the mount. The Inclino can also be mounted to the top bars if there is no room under because of obstructions. Also the mount is rotatable meaning it can be turned to clear. Just my view but I am sure Curt will take your comments into consideration.

Adrian T. · 03-08-2008, 12:30 PM

Quote:

Originally Posted by johnvon12

Just a quick comment regarding the mount. The Inclino can also be mounted to the top bars if there is no room under because of obstructions. Also the mount is rotatable meaning it can be turned to clear. Just my view but I am sure Curt will take your comments into consideration.

Thanks. I can see that there will be a lot of mounting possibilities. But anyway, it would be great to have a low profile mount. :whistling:

John V · 03-08-2008, 02:27 PM

Agreed...we will see what we can do...might be an option down the road to change out the mount. At this point things are already moving so we will see what can can do.

James T Mather · 03-09-2008, 11:26 AM

Hi guys - I have a question having trawled through the entire thread with no answer -

What bars does this thing connect to (15mm or 19mm)

Thanks

Matthew Rogers · 03-09-2008, 12:12 PM

Quote:

Originally Posted by jtm

Hi guys - I have a question having trawled through the entire thread with no answer -

What bars does this thing connect to (15mm or 19mm)

My understanding is that it doesn't matter! Right now the motor only has to hook onto one bar (like the Arri lightweight ff unit.) There was talk of putting it on a 15mm or 19mm two bar system so it would be harder to have the motor come off the lens.

Matthew

03-09-2008, 11:26 AM	#159
James T Mather Senior Member Join Date: Jan 2007 Posts: 937	Hi guys - I have a question having trawled through the entire thread with no answer - What bars does this thing connect to (15mm or 19mm) Thanks __________________ www.jamestmather.com

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-07-2008, 04:03 PM	#153
John V Senior Member Join Date: Jul 2007 Posts: 190	Curt has been in Hanover, Germany for Cebit for the past week. He will be back in the next few days. We expect to get the ordering system up within the next week depending on the schedule he gives me.

03-08-2008, 10:01 AM	#155
Adrian T. Senior Member Join Date: Jan 2007 Posts: 1,453	Curt, please take into consideration that the INCLINO mount will be low profile. As you can see on the following picture, the RED universal mount is too high to pass over an OConnor mount when using the ET bridge plate on a ET dovetail plate (green line marks the problem area). The mount of the ET bridge plate (right below the front of the camera) is way smaller. The space between the rods and the silver lever of the OConnor head is approximately 13 mm. So please try to make your mount smaller than that.

03-08-2008, 12:19 PM	#156
John V Senior Member Join Date: Jul 2007 Posts: 190	Just a quick comment regarding the mount. The Inclino can also be mounted to the top bars if there is no room under because of obstructions. Also the mount is rotatable meaning it can be turned to clear. Just my view but I am sure Curt will take your comments into consideration.

03-08-2008, 02:27 PM	#158
John V Senior Member Join Date: Jul 2007 Posts: 190	Agreed...we will see what we can do...might be an option down the road to change out the mount. At this point things are already moving so we will see what can can do.